Naipu B15017U01 Polyurethane Slurry Pump Frame Plate Liner
Polyurethane material for Slurry Pump Liners, 2/1.5 A H Pump impeller, A H Slurry Pump Impeller
u01 back liner, warman pump spares, Polyurethane wearing parts, Frame Plate Liner, u01 Front Liner, A H Pump liner
i) Used for pump side liners, where the peripheral speed of the impeller is higher than 27.5 m/s,( 58675382, 58675307, 58666638,and precluding the use of standard rubber) and used for impellers where occasional trash may damage a rubber impeller.
ii) Erosion resistance is greater where erosion is of a sliding bed type rather than one of directional impact.
iii) Has less erosion resistance to fine solids than natural rubber. Has greater erosion resistance to coarse sharp edged particles than natural rubber, in some circumstances.
iv) Unsuitable for temperatures exceeding 70°C and for concentrated acids and alkalies, ketone, esters, chlorinated and nitro hydrocarbons.
| Cover Plate Liner | A H Slurry Pump | Wet Parts Material |
| B1017 | 1.5/1B-A H | Natural rubber, Synthetic rubber, Polyurethane |
| B15017 | 2/1.5B-A H | Natural rubber, Synthetic rubber, Polyurethane |
| C2017 | 3/2C-A H | Natural rubber, Synthetic rubber, Polyurethane |
| D3017 | 4/3C-A H, 4/3D-A H | Natural rubber, Synthetic rubber, Polyurethane |
| E4018 | 6/4D-A H, 6/4E-A H | Natural rubber, Synthetic rubber, Polyurethane |
| F6018 | 8/6E-A H, 8/6F-A H, 8/6R-A H | Natural rubber, Synthetic rubber, Polyurethane |
| F8018 | 10/8F-A H | Natural rubber, Synthetic rubber, Polyurethane |
| G8018 | 10/8ST-A H | Natural rubber, Synthetic rubber, Polyurethane |
| FAM10018 | 12/10F-A H | Natural rubber, Synthetic rubber, Polyurethane |
| G10018 | 12/10ST-A H | Natural rubber, Synthetic rubber, Polyurethane |
| FAM12018 | 14/12F-A H | Natural rubber, Synthetic rubber, Polyurethane |
| G12018 | 14/12ST-A H | Natural rubber, Synthetic rubber, Polyurethane |
| H14018 | 16/14TU-A H | Natural rubber, Synthetic rubber, Polyurethane |
| U18018 | 20/18TU-A H | |
| Impeller Code | L Slurry Pump | Materials |
| RSL30018 | 300S-L | Natural rubber, Synthetic rubber |
| S35018 | 350S-L | Natural rubber, Synthetic rubber |
| TL40018 | 400ST-L | Natural rubber, Synthetic rubber |
| TL45018 | 450ST-L | Natural rubber, Synthetic rubber |
| Impeller Code | M Slurry Pump | Materials |
| F8018 | 10/8E-M, 10/8F-M, 10/8R-M | Natural rubber, Synthetic rubber, Polyurethane |
| F10018 | 12/10F-M, 12/10R-M | Natural rubber, Synthetic rubber, Polyurethane |
The Slurry Pump Polyurethane Impeller design is crucial as it influences flow patterns and ultimately, wear rates throughout the pump. The number of impeller vanes usually varies between three and six depending on the size of the particles in the slurry.
Most slurry pump casings are [slower" than their Water Pump cousins, primarily to reduce wear though lower internal velocities. Slurry Pump Parts including many types. Such as Slurry Pump Polyurethane Throatbush and Slurry Pump Polyurethane Back Liner, which replaceable with standard metal and rubber liners.
Horizontal Centrifugal Pump Wet End Parts Polyurethane Material:
| Compared with Metal | Compared with Plastic | Compared with Rubber |
| Light | HIgh impact resistance | High Anti-abrasion |
| Denoise | Elastic memory | High shear & tear resistance |
| Anti-abrasion | Anti-Abrasion | Excellent bearing capacity |
| Lower cost | Denoise | Thick section molding |
| Anti-corrosion | variablefriction coefficient | Gradient |
| Elastic | Elastic | Colorability |
| Impact resistance | Thick section molding | colorability |
| Flexible | Lower mould cost | Oil resistance |
| Easily molding | Better cold tolerance | Radioresistance |
| Non-conducting | Cold flow resistance | Wide hardness range |
| No-spark | Radioresistance | Pourability |
| Lower price | Long worklife | Lower mould cost |
Slurry Pump Parts
032: Frame Plate
060: Intake Joint
132: Discharge Joint
083: Throatbush
110: Volute Liner
147: Impeller | 122: Stuffing Box Seal
036: Frame Plate Liner
013: Cover Plate
018: Cover Plate Liner
124: Volute Liner Seal
041: Frame Plate Liner Insert |
Q1. How to garanty the slurry pump and spares quality?
A: All our pump and spare parts pass ISO 9001:2008 and CE certificate. Warranty time is 12 month except wet end parts.
Q2. What information should be known if I want to get a quotation?
A: Pump working conditions, Usage, Pump Capacity, pump Head, Slurry SG, The More the Better. Please offer me the type of the used pump that working now.
Q3. Naipu pump company product range?
A: Centrifugal pump, Slurry pump, Sand Pump , Gravel Pump, Dredging Pump, Clean Water Pump, Sewage pump, Chemical pump, Single stage pump, Double suction pump, Industry pump, Paper pulp pump, Mud pump, Sludge pump, etc
Q4. Delivery time:
A: For the Common Slurry pump and spare parts , the delivery time within 7-15 days. Special material and OEM production is longer.
Any question please contact Katherine Hou freely.
Contact Now
