AHR Synthetic Elastomer Lined Mechanical Seal Ash Pump
Mechanicial seals are not widely used in slurry applications, but their use in special circumstances is increasing. The mechanical seal consists of a stationary and a rotating face pressed together under mechanical and hydraulic pressure, to prevent leakage.
Alpha grade silicon carbide is the most common material used for manufacture of these seal faces.
Mechanical Seal Slurry Pump applications where a centrifugal seal cannot be used, and where the addition of water cannot be tolerated, provide the most likely areas for the use of mechanical seals.
Synthetic Elastomer Slurry Pump, Mechanical Seal Slurry Pump, Replacement Rubber Liner Pump, AHR rubber liners Horizontal Slurry Pump, OEM Slurry Pump, OEM Pump Spares.
AHR rubber liners Horizontal Slurry Pump are used widely used for many industry. Where most plants utilise wet separation systems.
The use of mechanical seals Synthetic Elastomer Slurry Pump in slurry applications requires extreme care and attention due to the limited reliability common in this developing area. The Replacement Rubber Liner Pump produced by Naipu pump.
Rubber Liners Slurry Pump performance parameters
Type | Max power (kw) | Capacity m3/hr | | Speed rpm | Max Efficiency % | | No. of Vanes | |
1.5/1 B-A HR | 15 | 10.8-25.2 | 7-52 | 1400-3400 | 35 | 2-4 | 3 | 152 |
2/1.5 B-A HR | 15 | 25.2-54 | 5.5-41 | 1000-2600 | 50 | 2.5-5 | 5 | 178 |
3/2 C-A HR | 30 | 36-75.6 | 13-39 | 1300-2100 | 55 | 2-4 | 5 | 213 |
4/3 C-AHR | 30 | 79.2-180 | 5-34.5 | 800-1800 | 59 | 3-5 | 5 | 245 |
6/4 D-A HR | 60 | 144-324 | 12-45 | 800-1350 | 65 | 3-5 | 5 | 365 |
8/6 E-A HR | 300 | 324-720 | 7-49 | 400-1000 | 65 | 5-10 | 5 | 510 |
10/8 F-A HR | 560 | 540-1188 | 12-50 | 400-750 | 75 | 4-12 | 5 | 686 |
12/10 ST-A HR | 560 | 720-1620 | 7-45 | 300-650 | 80 | 2.5-7.5 | 5 | 762 |
16/14 TU-A HR | 1200 | 1200-3000 | 11-42 | 250-450 | 82 | 4-9 | 5 | 1067 |
20/18 TU-A HR | 1200 | 1800-4000 | 12-44 | 200-350 | 82 | 5-10 | 5 | 1370 |
Horizontal Slurry Pump Rubber Parts
Such as the 8/6 Slurry Pump part code no.: F6147RR55 Impeller, F6018r55 Cover Plate Liner, F6036R55 Frame Plate Liner, F6083R55 Throat bush, EAM029RMR55 Expeller...
Various requirement for materials in the market for slurry pump, Naipu offering wet end part material as following. Rubber R08, R26, R33, NR55, S01, S21, S31, S42 and etc. Special materail: U01, EPDM, PU, CR, Hastelloy 276-C, Ferralium and etc.
Any question please contact Katherine Hou freely. katherine at naipump dot com
Mechanical Seal Slurry Pump Impeller Adjusting